Door Design · J-2002
Steel Entry Door with Wood Grain Finish
J-2002 gives a steel leaf the warmth of timber through a heat-transfer grain, so the entrance reads residential while keeping steel's stability in sun and rain. Each J-2002 is made to the project opening: 70 mm leaf, 90 mm frame, steel system with an aluminum trim. The powder-coated steel with a lacquered or wood-grain face can be matched to the existing facade before production.
70 mm door leaf and 90 mm frame; final configuration and overall frame dimensions are confirmed on your project drawing. Multi-point lock with anti-drill cylinder, and a fingerprint lock can be fitted on request.
Discuss This DesignWhy this design works
- Heat-transfer wood grain bonded to the steel face
- Grain tone matched across door and frame
- No sanding, staining or seasonal re-coating
Design details
- Style
- Warm modern
- Material / system
- Steel system with aluminum trim
- Configuration
- Single door
- Door leaf thickness
- 70 mm
- Frame depth
- 90 mm
- Maximum frame sizes by configuration
- Single: 1180 × 2500 mm; unequal double: 1580 × 2500 mm; equal double: 2180 × 2500 mm (overall frame; family limits)
- Core filling
- Aluminum honeycomb or foam filling, selectable
- Glass
- None, solid panel
- Locking
- Multi-point lock with anti-drill cylinder
- Smart lock
- Smart lock compatible
Heat-Transfer Grain on Steel: What It Can and Cannot Do
The grain is transferred into the coating on a steel face, so it sits on the surface rather than in the material. In daylight at a few metres it reads as timber, and it keeps reading as timber after a summer of sun and rain, which an oiled veneer would not. What it cannot do is move: there is no open grain to lift, no figure that changes with the light, and no board joints to follow.
That flatness is the point, but it also means the grain direction is the only thing giving the leaf a sense of height. Run it vertically on a 3 m leaf and the entrance reads taller than it is; run it across and the same leaf reads wide and low. The face is 1.0 mm galvanised steel over a honeycomb or foam core, so it stays flat across its width, and an MGO core replaces the foam where the project needs a fire-rated assembly.
Specification & ordering
Steel Entry Door Specifications and Ordering
Steel entry doors are quoted by sheet thickness, frame build and core, because those three numbers decide the weight, the security performance and the freight cost per door.
Maximum Frame Sizes by Door Construction
Width × height in millimetres, measured to the outside of the frame. Arched heights include the arch. Confirm the selected model, clear passage and any additional sidelights on the project drawing.
| Door construction | Single leaf | Unequal double leaf | Equal double leaf |
|---|---|---|---|
| Steel Entry Doors | 1180 × 2500 mm | 1580 × 2500 mm | 2180 × 2500 mm |
These are construction-family limits, not confirmation that every pictured design is available in every arrangement. Pivot doors are supplied as a single leaf only; unequal and equal double pivot doors are not offered. Fixed sidelights are separate from the opening leaf.
Technical specification
- Door leaf
- 1.0 mm galvanized steel sheet
- Frame
- 2.0 mm galvanized steel
- Core
- Aluminum honeycomb or water-based polyurethane foam as standard; fire-rated MGO board for project orders
- Configuration
- Single or double leaf, with or without glass
- Glazing
- None, solid panel
- Finish
- Wood-grain transfer, powder coat or custom finish
Ordering & supply
- Minimum order quantity
- 1 door for seven series. Steel Entry and Fire Rated: 1 door for custom orders, 5 doors for project orders.
- Sample lead time
- 25 days
- Production lead time
- 30–45 days
- Container loading
- Approx. 300 doors per 40HQ (2050 × 950 mm single leaf)
- Factory inspection
- Third-party factory inspection welcome
- Trade terms
- FOB Shanghai / Ningbo; Yiwu warehouse handover; DDP available
- Warranty
- 3 years on structure; 1 year on hardware and electronic lock components
Figures above are our standard build. Where a project falls outside them, we quote a custom variant against your drawings rather than build to the nearest catalogue size. Full series specification: Steel Entry Door.
Image gallery
Frequently asked questions
Will the grain fade outdoors?
The finish is UV-stable and bonded to a powder-coated steel face, so it holds colour on a west or south elevation.
Can it match an existing timber door?
Send a photo or a timber offcut and we will match the grain tone and direction.
Can this design be custom sized?
Yes. Every JMR Habitat door is built to the opening dimensions on your survey or drawing, including non-standard widths and heights.
Which materials and finishes are available?
This design is built in Steel system with aluminum trim. Powder-coated colours, wood-look and metallic finishes are available, and a physical sample can be approved before production.
How do I specify this door for a project?
Send the opening dimensions, a drawing or reference image and your finish direction through the inquiry form; the team returns a specification and drawing for approval.
Planning an entrance around this design?
Share your opening dimensions, finish preferences and configuration needs with our team.
Start an inquiry
JT-02
J-2009
J-2006